INSTRUMENT CONTROL PARAMETERS:    ECD-P
                       ---------------------------------------

   C:\MassHunter\GCMS\1\methods\PCB.M
      Fri Aug 19 12:40:54 2022

Control Information
------- -----------

Sample Inlet             : GC
Injection Source         : GC ALS
Injection Location:  Front


 No Sample Prep method has been assigned to this method.


=============================================================================
                                 6890 GC METHOD
=============================================================================

OVEN
   Equilibration time:  0.50 min
   Maximum temp:  330 C
   Initial temp:  150 C (On)
   Initial time:  0.50 min
   Ramps:
     #   Rate  Final temp  Final time
     1  35.00      220        0.00
     2  20.00      330        5.00
     3    0 (Off)
   Post temp:  0 C
   Post time:  0.00 min
   Run time:  13.00 min

FRONT INLET (SPLIT/SPLITLESS)
   Mode:  Split
   Initial temp:  220 C (On)
   Pressure:  12.0 psi (On)
   Split ratio:  5:1
   Split flow:  17.0 mL/min
   Total flow:  22.2 mL/min
   Gas saver:  On
   Saver flow:  15.0 mL/min
   Saver time:  100.00 min
   Gas type:  Helium

BACK INLET (UNKNOWN)

COLUMN 1
   Capillary Column
   Serial Number:  MR1
   Max temperature:  340 C
   Nominal length:  30.0 m
   Nominal diameter:  320.00 um
   Nominal film thickness:  0.50 um
   Calibrated length:  30.0 m
   Calibrated diameter: 320.00 um
   Mode:  constant flow
   Initial flow:  1.7 mL/min
   Nominal init pressure:  12.0 psi
   Average velocity:  35 cm/sec
   Inlet:  Front Inlet
   Outlet:  Front Detector
   Outlet pressure:  ambient

COLUMN 2
   Capillary Column
   Serial Number:  MR2
   Max temperature:  340 C
   Nominal length:  30.0 m
   Nominal diameter:  320.00 um
   Nominal film thickness:  0.25 um
   Calibrated length:  30.0 m
   Calibrated diameter: 320.00 um
   Mode:  (see column 1)
   Nominal initial flow:  1.7 mL/min
   Nominal init pressure:  12.0 psi
   Average velocity:  35 cm/sec
   Inlet:  Front Inlet
   Outlet:  Back Detector
   Outlet pressure:  ambient

FRONT DETECTOR (uECD)
   Temperature:  320 C (On)
   Mode:  Constant makeup flow
   Makeup flow:  60.0 mL/min (On)
   Makeup Gas Type: Argon methane 5%
   Electrometer:  On

BACK DETECTOR (uECD)
   Temperature:  320 C (On)
   Mode:  Constant makeup flow
   Makeup flow:  60.0 mL/min (On)
   Makeup Gas Type: Argon methane 5%
   Electrometer:  On

SIGNAL 1
   Data rate:  20 Hz
   Type:  front detector
   Save Data:  On
   Start Save Time:  2.50 min
   Stop Save Time:  13.00 min

SIGNAL 2
   Data rate:  20 Hz
   Type:  back detector
   Save Data:  On
   Start Save Time:  2.00 min
   Stop Save Time:  13.00 min

POST RUN
   Post Time: 0.00 min

INJECTOR 1
   Sample pre-washes:        2
   Sample pumps:  2
   Sample Volume (uL):  2.000
   Syringe size (uL):     10.0
   Pre washes from bottle A:  2
   Pre washes from bottle B:  1
   Post washes from bottle A:  1
   Post washes from bottle B:  1
   Viscosity delay (seconds):  0
   Pre injection dwell (min):  0.00
   Post injection dwell (min):  0.00
   Sample skim depth (mm):    0.0  (Off)
   Plunger Speed:  Fast
   Solvent saver:  Off
   Solvent Wash Mode:  A, B
   Waste Bottle Use: A Only

ALS ERRORS:
   On missing vial: pause

TIME TABLE
   Time(min)      Parameter & Setpoint





 Column 1 Inventory Number :  
 Column 2 Inventory Number :  



                        END OF INSTRUMENT CONTROL PARAMETERS
                        ------------------------------------